Implementasi Parameter Sistem Pentanahan Generator Melalui Transformator Distribusi Menggunakan Labview


Authors

  • Ayu Fitriani Universitas Tjud Nyak Dhien, Medan, Indonesia
  • Muhammad Fadlan Siregar Universitas Tjud Nyak Dhien, Medan, Indonesia
  • Syafriwel Universitas Tjud Nyak Dhien, Medan, Indonesia
  • Syofyan Anwar Syahputra Akademi Teknik Deli Serdang, Deli Serdang, Indonesia

Keywords:

Generator; Transformator Distribusi; Sistem Pentanahan; LabView; std C62.92.2TM-2017

Abstract

Determination of the generator neutral grounding system through a distribution transformer can be done through manual calculations. Many parameters are considered in the calculation to get the appropriate results there is the possibility of repeated calculations. This is very difficult and causes a large difference in the calculation results. Therefore, a computer-based computing system is needed to overcome this kind of problem. Several papers have developed the calculation of the required generator neutral earthing magnitude which considers the voltage level, short-circuit fault current and protection system against ground faults. This paper discusses modeling in designing generator neutral ground using the LabView Graphical User Interface (GUI) application. The goal is to be easier, faster and more accurate. As the implementation of the modeling used data from std C62.92.2TM-2017.

 

Downloads

Download data is not yet available.

References

Surya Hardi, Azwar Nasution, Modeling of Substation Grounding Grid Design Using LabView Graphical User Interface, ELTICOM, IEEE 978-1-7281-2475-9, 2019.

IEEE Std C62.92.2.™-2017, IEEE Guide for the Application of Neutral Grounding in Electrical Utility Systems, Part II—Grounding Of Synchronous Generator System.

ANSI/IEEE Std C37.101™-1995, IEEE “IEEE Guide for Generator Ground Protection” Approved 17 December 1981.

Verta Asi Manullang, Bonar Sirait, Purwoharjono,“Analisis Sistem Pembumian Netral Generator Pada Pembangkit Listrik Tenaga Uap Sei Batu 2×8.5 Mw Sanggau”, Program Studi Teknik Elektro Fakultas Teknik UNTAN Pontianak.

Dieter Braun, “Intermittent Line-to-Ground Faults in Generator Stator Windings and Consequences on Neutral Grounding” IEEE Transactions On Power Delivery, Vol. 25, No. 2, April 2010.

A.R. Sultan, M.W. Mustafa, M.Saini “Ground Fault Currents in Unit Generator-Transformer at Various NGR and Transformer Configurations” IEEE Symposium on Industrial Electronics and Applications (ISIEA2012), September 23-26, 2012.

IEEE Std 3003.1™-2019, “IEEE Recommended Practice for Grounding of Industrial and Commercial Power Systems“, Chapter-1 System Grouding, 2019.

IEEE Std C62.92.2.™-2017, IEEE “Guide for the Application of Neutral Grounding in Electrical Utility Systems”, Part II—Grounding Of Synchronous Generator System, 2017.

ANSI/IEEE Std C37.101™-2006, IEEE “IEEE Guide for Generator Ground Protection” Approved 15 September 2006.

David Shipp, Fellow, “Switching Transient Analysis and Specifications for Practical Hybrid High-Resistance Grounded Generator Applications”, IEEE Transactions On Industry Applications, Vol. 48, No. 1, January/February 2012.

Mohiuddin, Taqi. Nawrocki, Matt, “LabView Advance Programming Tecniques, Second Edition”, London,new York, 2006.

YU Lei , TIAN Bing , LEI Jinyong , HAN Bowen , WANG Gang2, “Effect of Load on Zero-Sequence Current in Low Resistance Grounding System with Complex Grounding Fault”, China International Conference on Electricity Distribution (CICED) 2017.

Agriselius, Asyer, “Analisis Pemilihan Pentahanan Titik Netral Generator Pada Pembangkit Listrik Tenaga Mikro Hidro 2 X 4,4 MW Nua Ambon Menggunakan Software ETAP 7.5”, Jurusan Teknik Elektro Institut Teknologi Nasional Bandung, 2014.

IEEE Std C62.92.2.™-2017, IEEE “Guide for the Application of Neutral Grounding in Electrical Utility Systems”, Part II—Grounding Of Synchronous Generator System, 2017.

Lazar, Irwin, “Electrical Systems Analysis and Design for Industrial Plants”, McGraw-Hill Companies, Inc, USA, Ch. 6, 1980.

Bitter, Rick, “LabVIEW™ Advanced Programming Techniques”, Second Edition, Taylor & Francis Group, 2007.

Tutorial metode optimasi pada LabView, jurusan Teknik Elektro, Universitas komputer indonesia,2005.


Bila bermanfaat silahkan share artikel ini

Berikan Komentar Anda terhadap artikel Implementasi Parameter Sistem Pentanahan Generator Melalui Transformator Distribusi Menggunakan Labview

ARTICLE HISTORY

Submitted: 2022-06-20
Published: 2022-06-30
Abstract View: 50 times
PDF Download: 58 times

Issue

Section

Articles